夾式送料機的用途
GS-906N簡易操作順序及說明

1． 材料線設定： 送料機/夾式送料機

固定座置放材料，手動閥On (No.1)夾住材料，材料下緣與模具同高或略高0-0.1mm.
2.送料時間設定
沖床：355°，送料機：送料至0（按沖床運轉方向，轉動皮帶輪，把副尺移卻至本尺0對齊）。
3.調整料厚：送料機/夾式送料機

A．送料機之設定：手動閥Off(No.2),料厚指示環向左旋轉旋緊之0為0.
B.人工調整：（1）.移動座于上死點（0°），手動閥On（No.1）,材料松緊之間，向左旋0.05mm并固定之。
（2）.固定座于上死點（180°）不放松，手動閥On（No.1）,材料松緊之間，向左旋0.05mm并固定之。
4.送距調整：
A.沖床時間：90°（送料終點。送料機/夾式送料機

B.松開M16螺母，以T型扳手調整至所需尺寸，并固定M16螺母。注：送距不穩定時，請留意送距調整螺絲固定環是否松動。
5.放松點設定：
A.時機：送料完成后，遵梢定位于材料。 送料機/夾式送料機

B.松開放松凸輪之M8螺絲，調整放松線使其對準放松點，固定M8螺絲即可。

GS-1006 simple sequence of opeations and description送料機/夾式送料機
1. Material line set
Place materials in holder, manual valve On (No.1) grip material, make material bottom align with the mold or slightly higher than 0-0.1mm

2 feeding time setting
When power press is 355 °, Feeding: Feeding to 0 (in the direction of press operation, turn the pulley, the deputy ruler has moved to align the scale 0).

3 Adjust material thickness
A. Feeder of the setting: Manual Valve Off (No.2), Counterclockwise rotate indicator ring of mterial thickness to “0”. 夾式送料機的用途
B. manual adjustments:
(1) Move the seat at the top position (0 °), manual valve On (No.1), turn 0.05mm in counterclockwise and fixed it.
(2) bracket at top position (180 °) and do not relax, manual valve On (No.1), turn 0.05mm in counterclockwise and fixed it.
4. Feeding pitch adjustment:送料機/夾式送料機
A. Press Time: 90 ° (feed end).
B. Loosen the M16 nut with T-wrench to adjust to the setting length, and fix M16 nut. Note: If the feeding pitch is unstable, please pay attention to adjustable screw loose or not.

5. Loose settings:送料機/夾式送料機
A. time: when finish feeding, follow pin in the material.
B. Loosen the screws M8 cam, adjust the line so it is on relax, fixation M8 screws.

型式
Feed Model

制造號碼
Serial No.:

材料寬度
Material width

放松角度
Pilot release
可調整Adjustable

材料厚度
Material thickness

送料機械
Feed Mechanism
曲軸傳動
Crankshaftdrive

送料長度
Feed length

安裝位置
Installation location
左邊
Left of press

送料角度
Feed angle

送料方向
Feed direction
左-右
L--R